WestBayWood floor priceHow to sell

Good flooring should choose good materials,WestBayWaterproof material, good materials should be natural, high and moderate density.Some people think that the higher the density of wood-based panel, the better. In fact, it is not. If the density is too high, its water absorption and expansion rate is also high, which is easy to cause size change and lead to floor deformation.Secondly, 'ISO quality system certification', 'ISO environmental system certification',In case of large-scale immersion or partial long-term immersion in water accidentally, if there is any leveling stay, it shall be immediately sucked away with a dry rag and allowed to be dry. It is forbidden to use an electric water heater to carry out dry or expose to the sun.Characteristics of fake and shoddy laminate flooringSaldus, SmellHigh concentration formaldehyde is a genotoxic chemical.In animal experiments,WestBayWhat is the of floor leather, high concentration inhalation in the laboratory can cause nasopharyngeal tumors. Look at the surface of the board.

Sticker method: stick the same wood grain paper on the front and back of the board. Use large-scale floor renovation machinery to polish the floor for many times, remove about .mm of paint layer, surface layer and wood layer, and make the floor surface in a new state of fine and smooth after fine sand.The floor corners are ground with a small grinder to make the whole smooth.Good flooring should choose good materials good materials should be natural, high and moderate density.Some people think that the higher the density of wood-based panel, the better. In fact, it is not. If the density is too high, its water absorption and expansion rate is also high, which is easy to cause size change and lead to floor deformation.Secondly, we should rely on advanced flooring production lines and equipment and rigorous technology to produce first-class flooring.Judging the quality of the floor can also be measured from the quality inspection certificate and other honorary certificates such as 'national quality inspection free products', 'ISO quality system certification', 'ISO environmental system certification', because the acquisition of these honors must refine the results of an enterprise&#;s operation.Production department,Impregnated paper laminated wood floor is a floor made of one or more layers of special paper impregnated with thermosetting amino resin, which is paved on the surface of wood-based board substrate such as particleboard and high-density fiberboard, with a balanced moisture-proof layer on the back and a wear-resistant layer and decorative layer on the front. It is hot pressed and formed. First, it is divided into thin and thick (more than mm and about mm in thickness).Laminate flooring contains a certain amount of formaldehyde,WestBayCeramic tile or wood floor, it is most suitable to choose products certified by the national environmental protection mark or inspection free products. easy care

If you want to polish a lot of things, tarpaulin and tape.Hardwood floors often need to be polished during installation.Test conclusion, Can strongly recommend to everyone that it is not easy to make mistakes: the wall is shallow, the ground is medium, and the furniture is deep.If the color of the wall in the home is very light, the floor color can choose intermediate color, and the color of furniture can be moderately dark. After the primer is dry, brush the first finishing coat and dry it.The fire rating reaches B which is unmatched by ordinary floors.Therefore, many public spaces are also paved with SPC floors, that is to say, this reason.WestBay, I like to choose soft floor leatherThe standard laminate floor surface should contain aluminum oxide wear-resistant paper. It has g, g, g and even lower. It is directly sprayed with aluminum oxide on the decorative paper. The state stipulates that the surface wear-resistant revolution of the laminate floor for indoor use should be more than revolutions. Only the floor with g wear-resistant paper can meet the requirements. The wear-resistant revolution of g wear-resistant paperThe number of revolutions can reach -, or even lower than g. It is good if the number of revolutions directly sprayed with aluminum oxide can reach -. For those with low wear-resistant revolutions, the material cost is relatively low; because of its low wear-resistant degree, the tool cost during processing is also low. On the contrary, the cost is much higher if the number of wear-resistant revolutions is high.Needless to say, for a long time, the lacquered cloth market was occupied by low-grade unlined lacquered cloth produced in Taiwan and other overseas countries, giving consumers the wrong message that China&#;s quality is not up to standard. In fact, after the inspection of these, the surface wear-resistant layer is only .mm, which is made of poorly processed and Recycled PVC. It does not meet the national standards for plastic coiled materials at all, so its service life is short, not comfortable to use.