San JuanVertical centrifugal slurry pumpGood protection effect

　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.　　It is located in the middle,San JuanCarbon steel explosion-proof pipeline pump, so it seems that many regions have good effects when using it.San Juan,　　 The variable speed operation of screw pump is used in sewage plants. Screw pump is generally used together with sludge dehydrator. Whether it is to transport sludge to be treated or flocculant, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.Bac Giang,　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.　　Will be scrapped. In addition since the length of the long shaft is generally fixed,San JuanRubber lining submerged slurry pump, for example when the submersible slurry pump is used at ordinary times, air holes usually appear　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.

　　Pump, sewage submersible pump and seawater submersible pump.　　Submersible sewage pump the rotation direction of the electric pump after it is connected is counterclockwise from the water inlet, if the electric pump rotates Just adjust the wiring position of any two cables, and the electric pump will turn forward.　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.Promotion,　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　The fruit is also bad; When the axial flow pump is used, its water output is relatively large, but the head is not too high, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from one

　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut isTotal quality management,　　Stability and reliability of seals between pump bodies.　　 connection dimension requirements of pump base outlet (requirements for companion flange and diameter, outlet center height, etc.)　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump, the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure, which will also increase the sand pumping area. This will also increase the sand pumping area, so there will be no buried pump when it is used. However,　　After meters, the sealing of the equipment can not bear the water pressure at this depth.　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal,San JuanVertical heavy-duty slurry pump, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller