WindsorSelf priming slurry pump wholesaleThere are many reasons for sustained strength

　　When the submersible slurry pump works, the pump needs to be placed on land the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water　　The submersible slurry pump is a kind of submersible pump which is connected with the motor and works underwater at the same time. In addition,WindsorISG single stage vertical pipeline pump, compared with horizontal slurry pump and vertical slurry pump, submersible slurry pump has the great advantage of flexibility and convenience, and is more suitable for various working conditions. The important technical points of submersible slurry pump are its motor andWindsor, no dilution of pulp, good shaft seal effect. It can be used when the slurry is not allowed to be diluted.　　What is the solution to this situation?Shijak,　　Stability and reliability of seals between pump bodies.　　What is the solution to this situation?　　 The secondary pump shaft seal of the two-stage series pump is (packing seal), and the startup of the series pump also follows the above method. Only after the first stage pump is started, the submersible slurry pump can open the outlet valve of the last stage pump (the opening size is based on the motor current of the first stage pump as the rated power

　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, and effectively reduces the wear of the host and anti vibration kinetic energy　　 hydrogen sulfide gas content mg/l　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way canGood reputation,　　After that, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened, and then start the pump.　　When the submersible slurry pump is used at ordinary times, cavitation usually occurs,WindsorPipeline pump body, which has a great impact on the impeller of the equipment itself. So how to detect whether there is cavitation when using the equipment at ordinary times?　　It is occasionally found that there is insufficient liquid supply when using, so what are the reasons for this situation and how to deal with it.

　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local placeshow,　　 To ensure the efficient operation of the submerged slurry pump,WindsorSubmersible sewage pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　 The valve shall be used to regulate the flow and head, and overload operation is not allowed.　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.Windsor,　　 Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping, so that the sand pumping area in this area forms a honeycomb,　　Generally, the diving depth of the submersible slurry pump is not more than meters and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, but because　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.