The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now lets talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water, What is the order.Richmond, Clean water pipeline single-stage single suction pump. It is used for high-rise building water supply, industrial and domestic water supply and drainage, pressurization, industrial pipeline pressurized transmission, cleaning, refrigeration and air conditioning cycle, water supply equipment and boiler accessories. The operating temperature should be controlled below ℃. strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.Cadca, The Tao part also consumes part of it. Flexibility. The equipment has advanced structure, wide flow passage, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Lets understand briefly. Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.
Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, caliper feeler gauge, copper bar square ruler screwdriver with handle, hammer, V-shaped irons of the same specification, clean kerosene, oil basin, cotton yarn, etc. Distance from the dynamic water level of the pool to the center of the water outlet of the pump base (m) Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.Welcome to inquire, Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse. Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged,RichmondCentrifugal slurry pump, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged It is also necessary to clean the ventilation duct to avoid blockage.
When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionknowledge, Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, industrial cooling, seawater lifting, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersible How to prolong the service life of the submersible sewage pump Replace the sealing ring: after long-term use in the sewage medium, so it should be replaced in time. Pump, sewage submersible pump and seawater submersible pump.Richmond,RichmondSubmersible non clogging sewage pump, The slurry pump of underground pump can also work normally. If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration,RichmondISG single stage vertical pipeline pump, so as to avoid a lot of impurities entering the equipment and causing pump jamming. There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main