Daniel FloresPipeline pumpPrices rose year-on-year

466HP159575805   ·  2022-11-23 00:21:52   ·   Machinery and industry equipment
a set of impeller for mixing will be added at the bottom of the equipment

  In addition to the main impeller inside the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its  Yes, such mechanical faults will cause the stator winding of the pump to be burnt out.Daniel Flores,  Microcomputer controller LW light: cause: the light is on and the machine stops, the water level is low, the water level returns to normal, and the machine starts automatically.   Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward, and roll the shaft by hand to press theKazakhstan,  If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,  If the oil seal ring of the shaft is seriously worn, replace it with a new one.  The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage


Daniel FloresPipeline pumpPrices rose year-on-year



   Selection of pipeline diameter: the selection of pipeline shall consider the one-time purchase cost, long-term operation cost and operation reliability.  Extractable.  Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time,Daniel FloresSubmersible pump can pump sewage, you should find a professionalEnergy costs,  Some impurities will entangle the impeller, so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.  Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal etc.  Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service life


Daniel FloresPipeline pumpPrices rose year-on-year



  When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionHigh quality and low price,  When the water pump is driven by electricity or diesel engine, thus forming a vacuum in the impeller. In this way, from a al point of view, it is to convert electrical or chemical energy into gravity   Lifting, loading and unloading of electric pump: remove the cable and disconnect the power supply.   install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.Daniel Flores,  The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze, rubber lining, stainless steel, titanium alloy and other materials used in China&#;s mining,Daniel FloresQJ submersible pump, chemical and water conservancy projects on the Yellow River are prone to wear, short service life and many faults  If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.  During adjustment,Daniel FloresVertical slurry pump, firstly loosen the support cover, then compress the nut, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation

0 Replies   |  until 2022-11-23 00:21:52 | 84 Views
Log inContent can only be published later