What is the cause of pump overload. There will be no insufficient liquid supply or other problems.Cuba, Driven by the pump products represented by stainless steel pipeline pumps, the whole pump industry is constantly moving forward, and with the raw material market driven by this,CubaIrrigation deep well pump, new stainless steel materials are constantly coming out. The continuous improvement of various technologies and specifications has driven the whole industrial chain to a higher direction. Stability and reliability of seals between pump bodies.Poetic Wizard, Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose Inspection before installation: Check the specification, size and quality of thick and thin accessories. There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method,CubaPipeline pump,CubaWater well pipeline pump, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main
Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment. Ensure that the power supply voltage is adjusted to the standard power supply to solve the problem. Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service lifeDirect material, Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower. Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal. The working properties of the two pumps are also different. Because the sewage pump is driven by a motor, it generally has good voltage impact resistance. The submersible pump is of the type of quick opening and quick closing, so it usually uses some small Flow and small pressure.
The packing seal, auxiliary impeller seal and mechanical seal are mainly used. Among them, and can also play a role intarget, Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized to Frequent opening and closing: the frequent starting of submersible sewage pump will affect its service life. Backflow will occur when stopped. If it is opened immediately, the motor load will start, resulting in excessive starting current and winding combustion. The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise so it is easy to burn out the motor.Cuba, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller! The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs. Pump. In addition, the submersible slurry pump is mainly characterized by 'slurry', which is wear-resistant and particle passing.
Cool Software Technology Company 2022-11-23 09:41:28 support 0 | be opposed to 0
FiberBison Thermal Insulation Co., Ltd. 2022-11-23 10:08:15 support 0 | be opposed to 0
Power protection pipe 2022-11-23 10:08:05 support 0 | be opposed to 0
Instrumentation and automation equipment research and development 2022-11-23 09:44:35 support 0 | be opposed to 0
electrification accessories 2022-11-23 09:46:19 support 0 | be opposed to 0