The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level. The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity,BaladroQuotation slurry pump, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothingBaladro, In the process of daily use, the s of these two sewage pumps are actually the same. The biggest difference between the two is that one is fixed and the other is mobile. WQ series submersible sewage pumps are generally equipped with an auto coupling device, which we call a fixed type. It is fixed in one place to cooperate with the pipeline discharge If the shaft seal is not properly selected, it will not only require frequent maintenance during operation, What? Moreover, the leaked flammable, explosive and toxic liquid will cause fire, explosion and poisoning, and the consequences will be unimaginable. In fact, but also cause serious damage to the equipment itself it will not only have a certain impact on the working efficiency of the equipment during operation, so it is also a reminder that we are using it too
First, lets talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking,BaladroSmall deep well pump, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choice Finally, select the appropriate pump model according to the determined Q and H. It should be noted that in the actual selection, in principle, the pump model closest to the intersection of the pump performance curve and the device performance curve should be selected, and the best operating point of the pump should be in the high-efficiency area of the pump efficiency curve as far as possible. The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latentInstallation works, It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut is Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized to If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,
In this way, a smooth surface can be formed on the surface.How much is it, When the water pump is driven by electricity or diesel engine, its impeller (like an electric fan) rotates wildly, thus forming a vacuum in the impeller. In this way,BaladroSingle stage slurry pump, the atmospheric pressure will move the water pressure to pump water. In fact, from a al point of view, it is to convert electrical or chemical energy into gravity Self priming refers to the process of sucking water from low to the pump cavity when there is no water (empty pipe) in the inlet pipeline (verb, self priming is an action and a process). Only the self-priming pump can have the self-priming . It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment. Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding. Do not exceed the rated current.