SanzakatDeep well pumpIntroduction to selection skills of operation methods

466HP159575805   ·  2023-02-27 01:50:16   ·   Machinery and industry equipment

   bind the exposed copper wire to the cable core evenly, heat it with an electric iron, and infiltrate tin evenly.  Water flow into the bearing damages the bearing.Sanzakat,  The main shaft of the water pump is bent or the main shaft of the water pump and the motor is not concentric or parallel.  Slurry pump Inappropriate model is selected when selecting the pump. In actual use, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pumpTaunggyi,  The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump,SanzakatSubmersible non clogging slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.  Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people   selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.


SanzakatDeep well pumpIntroduction to selection skills of operation methods



  Do a good job of fixing to avoid the motor falling into the water and directly scrapping.   within the estimated installation depth, the minimum inner diameter of the well is mm  Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth,SanzakatDeep well pump, so the concentration control is more free. Equipment directly submergedRecommendation and consultation,  The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent  Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment.   Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.


SanzakatDeep well pumpIntroduction to selection skills of operation methods



   There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps waterWelcome calls , the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.  In fact, as long as we understand the structure and working principle of the slurry pump, so we need to rotate the impeller of the slurry pump, and the connection between the impeller and the pump shaft is connected through screw threads.  It needs to be replaced in case of damage, swelling and deformation insufficient spring pressure, etc.Sanzakat breakage,  In addition to the method, materials shall be selected comprehensively according to the nature of corrosive medium, anti cavitation theory, corrosion mechanism of water pump and stress characteristics. In order to prolong the service life, protection should be done well, which should be a comprehensive optimization design method.  It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possible   The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.

2 Replies   |  until 2023-02-27 01:50:16 | 156 Views

Hongzheng Electronic Equipment Co., Ltd. 2023-02-27 10:45:26 support  0 | be opposed to  0

Your company SanzakatDeep well pump has a very good service attitude, thank you, and like you.

Hardware, electrical materials and mechanical conveying equipment 2023-02-27 10:21:31 support  0 | be opposed to  0

SanzakatDeep well pump Not bad, the price is worth it, just right.
Log inContent can only be published later