ManaguaGalvanized steel square pipe manufacturerWhat can I do to make it stronger

: it refers to the processing of square tube, which places metal in a closed Jane and applies pressure at the end to extrude the metal from the specified die hole to obtain finished products with the same shape and size. It is mostly used to produce non-ferrous metal materials. Square tube ferrous metal, steel and non-ferrous metal. Before introducing the classification of steel, square tube steel and non-ferrous metal.Stage ( & mdash; )Managua,General square pipes are stacked outdoors, and most of them are buried underground when in use, so they are easy to corrode and rust. In order to ensure the smooth flow of the pipeline, square pipes must have strong corrosion resistance. Once the pipeline is corroded, it will cause oil and gas leakage, which will not only interrupt transportation, but also pollute the environment, and may even lead to fire and cause harm.Stage ( & mdash; )Antwerp,Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe,ManaguaHot dip galvanized square pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )Comprehensive classification ordinary steel A. carbon structural steel: (a) Q (b) Q (b); (c) Q( C)； (d) Q( B)； (e) Q.Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.

Main uses of square tube: square tube is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.Tensile strength: - yield strength: & Ge; elongation: & Ge; mechanical properties of seamless pipe: tensile strength: - yield strength: ≥ elongation: & Ge; mechanical properties of seamless pipe: tensile strength: - yield strength: ≥ elongation: & Ge; mechanical properties of seamless pipe: tensile strength: - yield strength: ≥ elongation: & Ge; mechanical properties of seamless pipe: tensile strength: - yield strength: ≥ elongation: & Ge; square tube belongs to low alloy series. It is one of the materials of seamless steel pipe. In low alloy materials, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe and then cut into the required length. Stage ( & mdash; )Bidding,Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.The first is to remove the rust of the square tube. When removing the rust of the square tube, the steel wire brush is mainly used to polish its surface, which can effectively remove the loose or rusty rust on the surface of the square tube.Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, seamless square tube square rectangular tube, galvanized square tube, galvanized tube, old brand,ManaguaWhere are galvanized square tubes sold, price advantage and quality guarantee! However, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm, it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, and the total bending degree shall not be greater than .% of the total length. Galvanized qb square pipe for low-pressure fluid transmission,ManaguaGalvanized iron pipe, with standard number of gbt-. Representative materials: QA, qbqb, etc. It is mainly used for conveying water gas, air, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.Inspection items,Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.The difference between qb square tube and QA is that there are fewer impurities s and P and better low-temperature impact performance. From the welding point of view, when the impurity elements in the base metal are less, it is good for welding hot crack.High density may not be obtained by simple pressurization, and insulation shall be carried out at the same time.Managua,Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand, steel shot, iron wire section, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, which can not only completely remove rust, oxides and dirt, but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.Alloy steel: A. low alloy steel (total alloy element content & le; %); b. Medium alloy steel (total alloy element content > ~ %); c. High alloy steel (total alloy element content > %).The local heat release in the welding process of square tube can reduce the heat affected zone avoid the micro of thermal sensitive materials, and maintain the properties of materials.