Henri de Castries How much is a 20 cm I-beamThere are so many things to pay attention to in use

984HP143755493   ·  2023-03-18 12:31:40   ·   Building materials

When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties chemical properties, weldability and structural size.What is the purpose of flat steelHenri de Castries Cold. Small longitudinal crackAt Tayyibah,The delivery length of I-beam is divided into fixed length and double length, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No. and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method. Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, with the rapid development trend of high-quality hot strip mill production and the development of electric welding and testing technology, the welding quality has been continuously improved, the types, specifications and models of welded steel pipes are increasing, and seamless pipes have been replaced in more and more industries. Welded steel pipes are divided into straight seam welded pipes and spiral welded pipes according to the way of welding. Classified by production mode: classified by processing technology - electric arc welded pipe, resistor welded pipe, (high frequency,Henri de Castries How many bars are there in a bundle of 25, low frequency) gas welded pipe, furnace welded pipe.When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:Good reputation,Introduction to product knowledge of alloy pipe:I-beam, also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.As shown in the name I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.


Henri de Castries How much is a 20 cm I-beamThere are so many things to pay attention to in use



The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Recommendation and consultation,Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling,Henri de Castries 15CrMo alloy pipe in stock, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate,Henri de Castries Direct sales of welded pipe manufacturers,Alloy pipes are widely used in building materials, and the test standards of alloy pipes are also different. Alloy pipe has high hardness and can be used at many levels, such stainless steel plate can be applied.Application characteristics of I-beamAfter isothermal quenching treatment, the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment.

0 Replies   |  until 2023-03-18 12:31:40 | 93 Views
Log inContent can only be published later