KoprzhvnitzGalvanized spiral pipeHave entity

At this time, if the welding wire of the same material is used for spot welding where the thickness is insufficient, it shall be welded to the fixed thickness, ground and sandblasted, and repair welding shall be adopted where there are cracks even if the steel pipe with another large opening can be made up at one time.The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.Koprzhvnitz,The quality of the solid square tube after the square tube formwork removal and curing can be tested according to the requirements and the following ways: use a magnifying glass to observe whether there are non external force cracks on the structural surface of the solid seamless qb square tube. When non external force cracks appear on the surface of qb square pipe, the crack width on the structural surface of ordinary qb square pipe shall not be greater than .mm.When sand blasting or manual mechanical derusting is used, due to the falling off of the oxide scale of the galvanized square pipe, the metal on the surface of the galvanized square pipe is directly exposed in the air. If a primer is not applied in time, the surface of the galvanized square pipe is easy to rust again, affecting the adhesion of the paint film. I am engaged in all kinds of square tubes, square rectangular tubes, seamless square tubes, the overstock of inventory is easy to expire. Therefore, the main indexes of the paint must be rechecked before use, and the paint can be used only when the results meet the standards.Bayt Fajjar, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes, structural parts and parts widely used in chemical, petroleum, light textile, food, machinery and other industries.Section shape classification of large-diameter qb square tube square tube is classified according to section shape: simple section square tube & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Flower shaped square pipe, open square pipe, corrugated square pipe, special-shaped square pipe, large-diameter qb square pipe surface treatment classification square pipe is divided according to surface treatment: hot-dip galvanized square pipe, electro galvanized square pipe, oil coated square pipe, acid pickling square pipe, large-diameter qb square pipe purpose classification square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tool equipment,KoprzhvnitzQ235B square tube, machinery industry, chemical industry steel structure, shipbuilding, automobile, steel beam and column,KoprzhvnitzRectangular galvanized square pipe manufacturer, special purpose, large-diameter qb square tube wall thickness classification large-diameter qb square tube according to wall thickness Classification & mdash& mdash; Super large diameter qb square pipe, large diameter qb square pipe and thin-wall large diameter qb square pipe rectangular pipe are the names of square pipe and QB square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment. Generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe then rolled into a square pipe from the round pipe, and then cut into the required length. Usually pieces per bag. Qb square pipe, also known as square and rectangular cold-formed hollow section steel, is referred to as square pipe and rectangular pipe, code f and j respectively. The allowable deviation of wall thickness of qb square pipe shall not exceed plus or minus % of nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of wall thickness when the wall thickness is greater than mm, except for the wall thickness of corner and welding joint area.Compared with other welding, square pipe welding has many advantages, mainly because of the exothermic reaction, the material only needs to be heated below the melting point

With the improvement of production quality, the quality of square tubes is getting better and better. The quality of square tubes will affect our lives. Because the functions of square tubes are different, their characteristics and uses are different. I will introduce the characteristics and uses of square tubes in detail.Function index analysis of square tube - the strength acts on the parts in a great progress. The load on the parts is called the charge and trap load. The power of square tube destruction under the charge and trap load is called the charge and trap toughness.The floating mandrel mill is in its heydayaverage method,With the improvement of production quality, the quality of square tubes is getting better and better. The quality of square tubes will affect our lives. Because the functions of square tubes are different, their characteristics and uses are different. I will introduce the characteristics and uses of square tubes in detail.The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.Plasticity QB square plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.

Square tube nonferrous metals, also known as non-ferrous metals, refer to metals and alloys other than ferrous metals, such as copper, lead, zinc, aluminum, brass, bronze, aluminum alloy and bearing alloy. In addition, chromium, nickel manganese, cobalt square tube, vanadium, tungsten, titanium, etc. are also used in industry. These metals are mainly used as alloy additives to improve the performance of metals. Tungsten square tube titanium, molybdenum, etc. are mostly used to produce cemented carbide for tools. The above non-ferrous metals are called industrial metals. In addition, there are precious metals: platinum, gold, silver and rare metals, including radioactive square tubes.Administration,After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, mostly mm and mm. The square tube is allowed to deliver short and non fixed length products not less than mm, or in the form of interface tube, but the Demander shall cut off the interface tube when using it. The allowable deviation of the wall thickness of square pipe shall not exceed plus or minus % of the nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of the wall thickness when the wall thickness is greater than mm, except for the wall thickness of corners and weld areas. The weight of short gauge and non fixed gauge products shall not exceed % of the total delivery. For square tubes with a theoretical weight greater than kgm, it shall not exceed % of the total delivery. We have many different ways in square tubes. Different ways make square tubes have different characteristics. According to these characteristics,Koprzhvnitz350 galvanized square pipe, we can correctly select the appropriate application field, In this way, the use efficiency of square tube can be improved. Next, their accuracy is second only to that of fine polished surfaces. Therefore, cold parts generally do not need to be reprocessed, and a small amount only need finishing (grinding).The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted but the derusting quality level must be reached.Koprzhvnitz,Derusting grade for the construction process of epoxy, ethylene, phenolic and other coatings commonly used for square pipes, the surface of square pipes is generally required to reach near white grade (SA). Practice has proved that almost all oxide scale, rust and other dirt can be removed by using this derusting grade, and the depth of anchor grain can reach ~ & mu; m, which fully meets the requirements of adhesion between layer and square pipe The shot derusting process can meet the technical conditions of near white level (SA) with low operation cost and stable and reliable quality.So flat, and the size and thickness are not standardized, it can reflect that this square tube is a poor product& rdquo;Qb square tube, qb square tube, qb square tube, QB square tube, QB square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Qb square tube and I-beam are two products with different shapes. Under the condition of the same material, the bearing capacity of steel is the same, but their uses are very different. The shape is different. Qb square tube is a cuboid, and I-beam is in I-shape. The purpose is different. I-beam can be used as span and support. Square pipe is a little worse than span. It is no problem to do support. However, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt-) is a square tube for general structure and mechanical structure.