Joe BaboSelf priming non clogging sewage pumpThe price fluctuated slightly

　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choice　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submergedJoe Babo,　　 the mechanical seal adopts a new type of hard corrosion-resistant tungsten titanate material, which can make the pump operate safely and continuously for more than d~ hours.　　Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation,　　At the same time, the supporting pipelines in the pump room shall be provided with vibration isolation elasticity.　　In the mud pump,Joe BaboVortex pump and pipeline pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, the liquid effect is on the auxiliary impeller　　How to avoid this situation when the equipment is in use.

　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!　　Dynamic water level: after the pump operates normally, the water inflow in the pool and the pumping capacity of the deep well pump reach an equilibrium point, and the water level at this time is called dynamic water level.　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pumpranking,　　 It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large,Joe BaboBaigang deep well pump, resulting in the high temperature of the vacuum pump.　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged,Joe BaboSplit vertical pipeline pump, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, it is also possible that the temperature is too high due to the low voltage of the water pump.how much,　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.　　The sub bearing and cylindrical roller bearing can bear the maximum axial and radial loads of the pump. The bearing is lubricated with grease. The two ends of the bearing body are provided with sealing end caps, labyrinth sleeves and labyrinth rings, which can effectively prevent dirt such as mineral slurry from entering the bearing ensure the safe operation of the bearing and have a high service life.　　 Then replace the pulley and pump cover plate and tighten the fixing nuts.Joe Babo,　　If the oil seal ring of the shaft is seriously worn, replace it with a new one.　　What stands out is the sealing of the container. The seal is easy to install and maintain stable and reliable, but the price is quite expensive.　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.