High feverFreight elevator liftingCapacity effectiveness

transport flammable and explosive products and other products.The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted and the pressure gauge reads the pressure gauge.High fever, and it is very difficult to climb up from the first floor,High feverSimple guide rail type cargo elevator, let alone hold things. For this reason, people have invented elevators, which can easily reach the floors they want to go to. However, it will be very troublesome if it rains, which will affect the normal operation of the elevator. So what should be done correctly after the elevator enters the water?Always check the connections of the various parts of the hydraulic lift,High feverWhere can I sell elevators for goods,As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.

Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.There are three movable plates on both sides of the adjustment plate, which can effectively avoid accidental injury to the toes of the operator when the adjustment plate is lowered, so as to ensure the safety of the equipment.This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.Discount,The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)

Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers,High feverElevating cargo elevators require, carpets and floors are protected from humidity. Rusty fittings.technical service,Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.Therefore, before heavy platform operation, the operator should provide the operator with operational skills and safety information, including: operation content and requirements; safety matters and dangerous points; division of labor and scope of responsibility. The operator should not only check the condition of the vehicle and the operator, but also check the terrain environment, whether the flight and landing meet the needs of safety skills or the pre-established operation plan. If there is income and expenditure, corresponding measures should be formulated before starting to operate.Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.High fever,Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, inform the phenomenon of the accident you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.