Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped. It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, water pumps and generatorsIpis, Belt drive bearing assembly: the bearing assembly of this series of pumps adopts cylindrical structure, which is convenient to adjust the clearance between the impeller and the front and rear guard plates, and can be removed as a whole during maintenance. The bearing is lubricated with grease. The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.Issia, The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force. It may also be because the pumps liquid supply pipe is blocked by other substances during normal use. Basically, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people
Moreover, explosive and toxic liquid will cause fire, explosion and poisoning, and the consequences will be unimaginable. There are several reasons for the severe vibration of the pump body: the phenomenon of unbalanced rotation of the electric rotor. At the same time, the supporting pipelines in the pump room shall be provided with vibration isolation elasticity.Variable cost, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump. Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped. Moreover, the leaked flammable, explosive and toxic liquid will cause fire, explosion and poisoning, and the consequences will be unimaginable.
One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. Whenrecommend, After a certain value,IpisSmall deep well pump, water will also vaporize, which is called the vaporization pressure of water at this temperature. Remove the wire guard water strainer and cut the cable from the lead and the three core cable or flat cable connector. Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for useIpis, The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage The solution to the excessive temperature of the water pump: when selecting the motor,IpisBaigang deep well pump, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades,IpisUsed pipeline pump, but pay attention to adjusting the vacuum pump Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand, so as to move the sand pumping place back and forth for sand pumping, so that the sand pumping area in this area forms a honeycomb
Pan Construction Engineering Company 2022-11-02 22:06:54 support 0 | be opposed to 0
chung hoon trading co., ltd. 2022-11-02 23:22:29 support 0 | be opposed to 0
JP Cabinet 2022-11-02 23:20:30 support 0 | be opposed to 0