San jositoRubber lining submerged slurry pumpWorking pressure product specifications and parameters
During adjustment, firstly loosen the support cover, then compress the nut,San jositoQJ submersible pump, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.San josito, Shaft seal part auxiliary impeller shaft seal: through the impeller action of a reverse centrifugal force, prevent the slurry from leaking out. When the positive pressure at the inlet of the pump is not greater than % of the pressure at the outlet of the pump, and the auxiliary blade shaft seal is not required Other ysts believe that, at least in recent years, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore,San jositoBaigang deep well pump, the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, especiallyJendouba, When stopping the operation of the submersible slurry pump close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improved
In this way, the solvent in the pump is often less, and the power consumption is also less, and the efficiency of the pump in use is often improved, and the fact is In order to meet the use requirements of slurry pumps in different industrial fields and working conditions, we have continuously carried out research, development and improvement, so that we have different series,San jositoSelf priming slurry pump wholesale, each series has a variety of specifications and models, and different series of products have different performance and s. Let&#;s learn about it below Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.Superior quality, If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming. The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage! When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged
The working properties of the two pumps are also different. Because the sewage pump is driven by a motor, it generally has good voltage impact resistance. The submersible pump is of the type of quick opening and quick closing, so it usually uses some small Flow and small pressure.supply, The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance when the design flow is required, the dynamic water level of the well is m Promote the continuous expansion of the sales network group.San josito, The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron bronze, rubber lining, stainless steel, titanium alloy and other materials used in China&#;s mining, chemical and water conservancy projects on the Yellow River are prone to wear, short service life and many faults The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, the power supply across the country has been tense again we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year, there is still a large gap after China&#;s power balance.