Saint AnneBaigang deep well pumpProduct trends and emerging categories

　　 Cutting blades can be selected to cut some large block solid substances into pieces during use, so that blockage can be avoided during reuse.　　What?Saint Anne,　　In addition, for different media pumped by the deep well pump, the pump components can be made of corrosion-resistant materials suitable for various media, such as copper, L and other stainless steel.　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.Waffle,　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.　　Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time,

　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition,Saint AnneCarbon steel explosion-proof pipeline pump, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current.　　However, with the increase of pump operation time,Saint AnneCorrosive pipeline pump, it is bound to be accompanied by the decrease of pump efficiency and the wear of flow passage components. The most serious parameter affecting the pump characteristic curve is the wear of the pump impeller. After the wear of the impeller, it is equivalent to the downward movement of the pump H-Q curve, which reduces the flow and head　　Pump, sewage submersible pump and seawater submersible pump.offer, the medium slows down because the flow channel is also gradually expanding.　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.

　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improvedInstallation works,　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.　　 Drain the water filled in the motor.　　When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionSaint Anne, submersible slurry pump has also responded to the market demand. At the same time, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceeds　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pump　　The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure wide flow passage, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles strong sewage discharge capacity, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.