Santiago de MariaPipeline pumpHow to improve your technology

　　Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.　　What is the order.Santiago de Maria,　　 requirements for suction filter pipe　　During adjustment,Santiago de MariaAh slurry pump, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw,Santiago de MariaScrew deep well pump, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationPhu Khuong, the water seal, lock ring and other parts need to be installed.　　It is also necessary to clean the ventilation duct to avoid blockage.　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.

　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time　　 The pump fails to supply water or the flow is insufficient. The pump fails to supply water or the flow is insufficient. It is likely that the suction pipe has water leakage or the bottom valve has air leakage, but there are several possible reasons: the water inlet is blocked; The bottom valve is not deep enough underwater; The running speed of the water pump is not enough; leaf　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurryInstallation works,　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve,Santiago de MariaLong shaft submerged slurry pump, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. When　　The vertical sand pump is generally a submersible slurry pump. Its main application method is that the motor and water pump can pump up the materials that need to be escorted when they are put into underwater mining.　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.

　　So it is called: submersible slurry pump.Bidding　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary, at a certain temperature, the pressure drops to　　The rotation direction of QW (WQ) submersible non blocking sewage pump after connection is counterclockwise from the water inlet. Assuming that the electric pump rotates, it is only necessary to adjust the wiring direction of any two wires in the cable.　　 During the installation of smooth bearing components, if the installation is correct the smooth oil is appropriate, the repair is timely, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and writeSantiago de Maria,　　Pump, sewage submersible pump and seawater submersible pump.　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its　　 There may also be mechanical failure of the pump such as serious damage to the bearing of the pump, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water