GuadeloupeVertical slurry pumpHow to repair after corrosion

　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.　　Balance of.Guadeloupe,GuadeloupeVertical centrifugal slurry pump,　　 Use a V insulation resistance meter to measure the insulation resistance between phases and phase to ground of the electric pump motor, and the value shall not be less than m Ω. Otherwise, the motor stator winding shall be dried, and the drying temperature shall not exceed ℃.　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.Bosaso,　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.　　After the submersible slurry pump leaves the factory, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, the flow area in the pump body increases, which makes the flow increase after the impeller is cut.　　 The motor output of the large flow submersible pump is too high, there are other electric equipment on the user&#;s site, and the user&#;s Transformer composition capacity is too small to start the submersible pump. You can use a suitable transformer or turn off other electrical equipment that meets the power consumption of the submersible pump.　　 the submersible slag pump is often used to transport pulp containing solid particles, so the wear resistance of the pipeline should also be considered.device management,　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local places　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal,GuadeloupeISG single stage vertical pipeline pump, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　Second, the power used is not matched, otherwise the mechanical seal will be burned.Where is it so I

　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water,　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.　　If there is no liquid in the cavity of the self-priming centrifugal pump of the submersible sewage pump, the gas-liquid foam mixture cannot be formed and the air cannot be pumped. In order to ensure the speed and reliability of air extraction,GuadeloupeSubmersible non clogging slurry pump, sufficient liquid should be filled in the pump cavity before starting. What time would you like　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,Guadeloupe,　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.　　It generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, water pumps and generators　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.