La RomanaHH slurry pumpFunctions of platform customer service

　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pump　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without itsLa Romana,　　In order to maintain the original treated water volume without increasing the number of water pumps, the liquid level in the storage tank can be increased by adjusting the floating ball in the liquid tank. After the liquid level in the storage tank is increased, the head at the intersection of the two curves becomes smaller and the flow remains　　After a certain value, water will also vaporize, which is called the vaporization pressure of water at this temperature.Florida,　　 When stopping the operation of the submersible slurry pump, and After that cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.　　The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.

　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so that　　Damage to the rotor.　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, industrial cooling, farmland irrigation seawater lifting, ship load adjustment, landscape fountains,　　In fact, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes, as well as for advanced technologies, especially in the mining, chemical, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corroded　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze, rubber lining, stainless steel,La RomanaSmall deep well pump, chemical and water conservancy projects on the Yellow River are prone to wear, short service life and many faults　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.

　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid),La RomanaPipeline pump, wrap the insulation layer and sheath layer, and dry it naturally.Workshop cost,　　The balance ring is also disassembled; Then remove the last stage impeller and the key back and the middle section including the guide vane; in addition, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurry　　Actually, you don&#;t have to worry about this. First of all, stainless steel has very strong anti-corrosion ability compared with products that are easy to rust. When many friends buy stainless steel deep well pumps, their manufacturers will apply a thin anti-corrosion coating on the outer layer of the equipment according to the needs of consumers. as　　 Next, the water seal, lock ring and other parts need to be installed.La Romana,　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump　　During adjustment,La RomanaCirculating hot water pipeline pump, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation　　If the shaft seal is not properly selected, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.