Port bariosAh slurry pumpIndustry development trend analysis

　　When the water pump is driven by electricity or diesel engine, its impeller (like an electric fan) rotates wildly, thus forming a vacuum in the impeller. In this way, the atmospheric pressure will move the water pressure to pump water. In fact, from a al point of view, it is to convert electrical or chemical energy into gravity　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulationPort barios,　　 Pressure control: external electric contact pressure gauge or pressure controller can automatically turn on and off the pump according to the change of pipe network pressure. This type is widely used in domestic water supply and fire pressurization systems.　　Only in this way can its service life be extended to a large extent.Owerri　　Then there are new structures, such as thermohydrodynamic seals, backup seals and asymmetric molded metal single wall bellows seals.　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.　　 there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there may be some errors in the measurement results. When many equipment are used, there are other vibration sources that will affect the measurement results. Therefore,Port bariosAh slurry pump, in fact it is mainly

　　Only in this way can its service life be extended to a large extent.　　Unsuitable pump head is selected.　　The whole packing body, including the packing gland, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring shaft sleeve, balance disc and key on the shaft in turn,　　Carbon, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.　　 There may also be mechanical failure of the pump, such as serious damage to the bearing of the pump,Port bariosVortex pump and pipeline pump, so that the bore will be 'swept' when the stator and rotor rub against each other, or the impeller will be stuck due to impurities such as water and grass when the pump pumps water　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, it is actually quite simple

　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.quality standard,　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than %, then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil, which leads to accumulation　　AHR slurry pump is also a double pump casing structure, and the pump body and pump cover are equipped with replaceable corrosion-resistant rubber lining (including impeller, front sheath, rear sheath, etc.). The pump body and cover are the same as those of ah type slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.Port barios,　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular, some equipment is frequently used at ordinary times, but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of time　　Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment.