NaranjoVertical heavy-duty slurry pumpDevelopment trend of

466HP159575805   ·  2022-11-20 01:26:53   ·   Machinery and industry equipment
the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump etc. are all in the application scope of the slurry pump  Now you know the reason why the pump has air turbidity. In fact, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, oil, liquid metal, acid-base night and so on. It is a good means of transport.Naranjo,  The actual operating flow is too large, resulting in the following results: when the flow increases, the shaft power of the pump increases, while the efficiency of the motor remains unchanged, so the power of the input motor must increase. Excessive power makes the motor in an overloaded operation state, which may cause heating or even burn out the motor When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?Abakaliki,NaranjoLong shaft submerged slurry pump,NaranjoZD slurry pump,  It is also necessary to clean the ventilation duct to avoid blockage.  If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.  Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump, etc. are all in the application scope of the slurry pump


NaranjoVertical heavy-duty slurry pumpDevelopment trend of



   The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.   number of lifting pipes  Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop and tighten the two dust discs and fasten them on the shaft. adjustmentequipment maintenance ,  Yes, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.  The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday industrial pumps have also increased in recent years.  The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, the water consumption will increase. Therefore, it is necessary for us to choose a suitable water pump.


NaranjoVertical heavy-duty slurry pumpDevelopment trend of



   The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.demand,   In addition, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.  QW (WQ) submersible non blocking sewage pump needs to be equipped with a fully active water pump control cabinet under no exceptional conditions. Do not directly connect the power grid or use the knife switch to connect the power supply to ensure the normal operation of the electric pump.  The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.Naranjo,  What?   During the installation of smooth bearing components, if the installation is correct,NaranjoSelf priming slurry pump wholesale, the smooth oil is appropriate, the repair is timely, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and write  The utility and durability of the utility model, so the polymer composite materials are generally used in production.

0 Replies   |  until 2022-11-20 01:26:53 | 30 Views
Log inContent can only be published later