When starting the slurry pump,GuadalupeSubmersible pump can pump sewage, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionGuadalupe, The water pump is not installed firmly or installed too high. The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.Phitsanulok, Inspection before installation: Check the specification, size and quality of thick and thin accessories. If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming. Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump,GuadalupeAh slurry pump, and the investment is lower.
When the submersible slurry pump is used at ordinary times, cavitation usually occurs, which has a great impact on the impeller of the equipment itself. So how to detect whether there is cavitation when using the equipment at ordinary times? If there is a gap in the actual work, if the pipeline can not absorb water normally,GuadalupeDeep well pump, and then check the cause of the abnormal suction range of the pipeline pump and solve it. After the submersible slurry pump leaves the factory there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.Inspection items, The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submerged When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in addition After a certain value, water will also vaporize, which is called the vaporization pressure of water at this temperature.
With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our companys underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.Process inspection Screw it down, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn. The sheath is divided into front sheath and rear sheath, which are made of natural rubber. The lining is made of high chromium alloy, so it has good wear resistance. It can be used until it is worn out, so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service lifeGuadalupe, in addition, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate. the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.
Dongxiao Power Technology Co., Ltd. 2022-11-06 10:03:41 support 0 | be opposed to 0
Sanshengkou Dezhong Wood Processing Co., Ltd. 2022-11-06 08:22:50 support 0 | be opposed to 0
Except futures consultation 2022-11-06 09:11:47 support 0 | be opposed to 0
FRP composite insulation cross arm 2022-11-06 08:04:35 support 0 | be opposed to 0
Distribution box 2022-11-06 08:56:39 support 0 | be opposed to 0