San Pedro ayampukVertical centrifugal slurry pumpWhat are the four major technical standards

466HP159575805   ·  2023-03-24 18:16:45   ·   Machinery and industry equipment
then tighten the bearing seat

  Stop, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose   important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.San Pedro ayampuk,San Pedro ayampukSelf priming slurry pump wholesale,  Operation, maintenance and upkeep During the operation of the electric pump, always observe the current, voltmeter and water flow, and strive to make the electric pump operate under the rated working condition.  The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latentKalutara,  Second, so the motor temperature will be too high after long-term overload operation; In addition, so I  The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore it is necessary for us to choose a suitable water pump.  Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box,San Pedro ayampukLong shaft submerged slurry pump, and then place the filler.


San Pedro ayampukVertical centrifugal slurry pumpWhat are the four major technical standards



  Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.  Slide until the active coupling is in place. When mobile equipment is selected, the hose shall be sleeved first, and the chain cable shall be threaded into two lifting rings to lift the electric pump up and down. Be careful not to use the cable as a rope to avoid danger.   selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, particle size, shape, hardness, concentration, acid, alkali and other characteristics of the transported materials.Create brilliance,  Rate.  Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose  Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, sewage submersible pump and seawater submersible pump.Statistics,  Some impurities will entangle the impeller, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.  The deep well pump works underwater. Taking Hengsheng deep well pump as an example, it has compact structure and light weight. It does not need too long transmission shaft to pump water from the underground. Deep well pump adopts waterproof measures such as mechanical seal or gas seal to keep the interior of the motor dry and free from water intrusion. Hengsheng pump today  Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.San Pedro ayampuk  Friction resistance due to bearing and packing; Friction between impeller and water during rotation; The vortex of water flow in the pump, gap reflux, inlet and outlet impact and other reasons. A part of the power must be consumed, so it is impossible for the water pump to completely change the power input by the power machine into effective power, in which the constant active power   To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump, the motor shall not exceed the rated current of the motor. Monitor oil seal and bearing at any time  The pump should be divided into two aspects: electricity and machinery. As for machinery, you can compare the previous maintenance records. The second is electricity. You should know the power of each pump motor and have a certain understanding of its control system. Slurry pump with mechanical seal

0 Replies   |  until 2023-03-24 18:16:45 | 98 Views
Log inContent can only be published later