KemiSelf priming slurry pump wholesaleWhat are the common software faults of the system

　　This phenomenon shows that the failure of the pump is not only a material problem, but also reminds the pump designers and producers that in addition to good working conditions, high reliability and long service life. The pump shall be designed in addition to the conventional design method of fluid mechanics　　At present, mechanical seals occupy an increasing share in the slurry pump seal market.Kemi,　　 for new or replaced deep well submersible pumps, after hours of use, check it once a month. At the same time, check whether the shielding sleeve between the motor rotor and stator is well sealed. Try to reduce the number of starts in use.　　To repair the equipment. Submersible slurry pump is a machine used to transport liquid. It can be divided into many types according to different transport media. Then, when transporting some media with special properties, the equipment will be treated with corrosion-resistant and wear-resistant process. Only in this way can the equipment be improvedKangdong-up,　　Stop then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose　　.　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.

　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section,KemiIrrigation deep well pump, the fixing nut on the shaft shall be　　Actually, you don&#;t have to worry about this. First of all, stainless steel has very strong anti-corrosion ability compared with products that are easy to rust. When many friends buy stainless steel deep well pumps their manufacturers will apply a thin anti-corrosion coating on the outer layer of the equipment according to the needs of consumers. as　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the number of stops and starts of the pump the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.Pursuit of excellence,　　Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump, dredging pump, desilting pump, etc. are all in the application scope of the slurry pump　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.

　　If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.reform,　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.　　 Long term dehydration operation of submersible sewage pump: since the submersible sewage pump uses water as cooling water, the motor may overheat and burn due to long-term dehydration.　　 After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.Kemi,　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed,KemiBaigang deep well pump, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.　　 The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.