MarianDN15 galvanized square pipeProportion of effective varieties

Precision inner diameter square tubes for hydraulic and pneumatic cylinders (gb-) are cold drawn or cold-rolled precision square tubes with precision inner diameter for hydraulic and pneumatic cylinders.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear,MarianGalvanized square pipe, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel rail, large-diameter steel pipe, forging, wire rod, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets,MarianGalvanized conduit size, or thin-walled steel pipes, and generally adopts ordinary closed warehouse, that is, the warehouse with roof, enclosure, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodMarian,Use classification square tubes are divided into: square tubes for decoration, square tubes for machine tool equipment, square tubes for mechanical industry, square tubes for chemical industry, square tubes for steel structure, square tubes for shipbuilding, square tubes for automobile, square tubes for steel beams and columns, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse, that is, the warehouse with roof, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, The storage period of materials can be extended, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodAsyut,The appearance of fake and inferior square tubes often has pitting. Pockmarked surface is an irregular uneven defect on the surface of square lead pipe due to serious wear of rolling groove. Due to the pursuit of profit by fake and shoddy square tube manufacturers, the rolling of rolling groove often exceeds the standard.For transportation: water supply, drainage, sewage treatment engineering, mud transportation, marine water transportation.Square tube has a wide range of application fields. Its main field is the construction industry, which promotes the development of economic construction. Because the production process of square tube hole is different the production design of square tube hole is also different. Next, I will introduce in detail the types of tube hole design below.

Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand, steel shot, iron wire section, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, which can not only completely remove rust, oxides and dirt, It can also achieve the required uniform roughness.Square tube saves raw materials: the material rate of cold parts can usually reach more than %. For example, the material rate of pin cutting of brand automobile is %, while the material rate when cold is used is increased to %; For another example, after the universal joint bearing sleeve is changed to cold, the material rate is increased from % in the past to%. It can be seen that the use of cold production of mechanical parts can save a lot of steel and non-ferrous metal materials.Classification of square pipe material square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe according to material. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, etc.technological innovationStructural stainless steel square pipe (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes, structural parts and parts widely used in chemical, petroleum, light textile, food, machinery and other industries.Product description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance, and good low temperature toughness.Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present,The pipeline is only subject to chemical pickling,MarianPrice of galvanized square pipe, which can remove oxide scale, rust and old coating. Sometimes it can be used as the reprocessing after sand blasting. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the surrounding environment. The square tube shall be submitted for acceptance in batches, and the batch rules shall comply with the provisions of corresponding product standards.Functional index analysis of square tube - commonly used are square tube Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV). Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.MarianThe surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.With the progress of the times and the development of science and technology, the application fields of square tubes are widely divided. The main fields are the construction industry. Affected by the environment and weather, square tubes will also rust for a long time. How to improve the rust resistance of square tubes and what are its rust resistance? Let me give you a detailed introduction below.Square tube has a wide range of application fields. Its main field is the construction industry, which promotes the development of economic construction. Because the production process of square tube hole is different, the production design of square tube hole is also different. Next, I will introduce in detail the types of tube hole design below.