KaramakHow much is the I-beam of 18Product Range

H-beam is a widely used profile in steel structure buildings. It is different from I-beam. The first is the flange, and the second is that the inner surface of the flange has no inclination, and the upper and lower surfaces are parallel. The section characteristics of H-beam are obviously better than those of traditional I-beam, channel steel and angle steel.After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.Karamak, In order to ensure the welding quality of pipes, welders shall be trained, tested and qualified. In addition to the basic theory, the welder should consider the operation skills. The pipe welding process may include several postures of overhead welding, vertical welding and overhead welding (when the pipe cannot rotate). The size of current should be selected to take into account the formation of vertical welding and overhead welding (some pipes are not very large, and the current cannot be adjusted in the middle of one formation). In the process the stability and formation of arc should be controlled, It can swing properly, and the forming shall be well combined with the necessary swing.Its heat sealing effect is remarkable. It can be directly buried immediately which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Pisco,The specification of pass design I-beam is expressed in cm of waist width. For example the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition I-beam can also adopt special rolling method.Nitriding: also known as nitriding, it is the process of penetrating nitrogen atoms into the surface layer of steel. At present,KaramakHow much is a meter of welded pipe,KaramakHow much is 90 galvanized pipe per meter, gas nitriding is widely used in the production of alloy steel pipe. Miscellaneous scab

Greatly reduce the environmental pollution caused by abrasion, damage and blanking, and increase the labor cost of material cleaningWhy are galvanized pipes so good?The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.Home page recommendation,Application scope of alloy pipeI-beam is widely used in buildings or other metal structures.Key technical characteristics of alloy pipe:

I-beam has the dual properties of high hardness and toughness materials. Compared with other engineering wear-resistant materials in China, such as various alloy steel plates, cast wear-resistant plates, cast stones, rubber, polyurethane, etc., it has irreplaceable comprehensive excellent properties.property right,Karamak3087 seamless pipe manufacturer,When we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know: Because the zinc coating has excellent ductility, it can be formed by cold stamping, rolling, bending and so on without damaging the coating.Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.Karamak,Defects of alloy pipe and solutions:Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane