BrandySingle suction slurry pumpWhat are the advantages of manufacturing technology

　　 Selection of pipeline diameter: the selection of pipeline shall consider the one-time purchase cost, long-term operation cost and operation reliability.　　Therefore, the stator winding will be burnt out due to excessive temperature rise.Brandy,　　In fact, stainless steel is not only advocated in the medical industry, but also widely used in the water pump industry. The stainless steel submersible pump of denang pump is one of them.　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.Camayenne,　　The vertical sand pump is generally a submersible slurry pump. Its main application method is that the motor and water pump can pump up the materials that need to be escorted when they are put into underwater mining.　　What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use, the pump itself generally needs to be placed on land for use,BrandySingle stage slurry pump, but its suction pipe needs to be placed in water　　The pump can often be selected according to the specific requirements of lift flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance

　　 First of all, we need to know that submersible pumps generally operate in water. In fact most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps may　　The course can be stronger.　　Promote the continuous expansion of the sales network group.Honesty and mutual benefit, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race,BrandySewage pump diving, bearing gland and retaining sleeve　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.

　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.OK or not?,　　If the oil seal ring of the shaft is seriously worn,BrandyDeep well pump, replace it with a new one.　　The equipment of this series of sewage pumps can be fixed or mobile. When the fixed active equipment is selected, the chain cable shall be separately threaded into (against the pump outlet,　　What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use, the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in water　　After the submersible slurry pump leaves the factory, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.　　In the mud pump the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller