Frederick BayGarden wood floorOnly by continuous R&D and innovation can enterprises develop better

From the perspective of environmental protection, the thin one is better than the thick one. Because the thin one uses less glue per unit area. The thick one has less density than the thin one, and the impact resistance is poor, but the foot feel is slightly better. In fact, there is little difference between the two. In fact, there is no difference between the thickness and quality of the two kinds of floors. The key is to see personal choice. waterproof, PVC has no affinity with water, and will not mildew due to high humidity.In southern areas with more rainy seasons, SPC flooring will not be deformed due to moisture, so it is a good choice for flooring.Frederick Bay, Recyclable: reduce urban construction waste, recycle construction waste and reuse old floors.In addition, there are impact resistance, anti environmental pollution, anti sunlight, anti smoke, easy installation, easy maintenance, etc.Murgab,When assembling the solid wood floor, do not be too loose or too tight.The assembly relaxation shall be reasonably arranged according to the temperature of the indoor environment. The assembly relaxation will produce a large gap with the shrinkage of the floor.The assembly is too tight and the floor is arched when it expands. Good wear resistance and stabilityThe standard specifications are adopted by most members of the European flooring Producers Association. This is still the case. China also adopts the standard specifications when importing the most advanced laminate processing lines in the world. In other words, the products of large laminate manufacturers processed by imported lines are still the standard specifications. There are many dealers in the market who flaunt themselvesOur products are imported. It is often said that 'imported ones have no wide plate specification and thickness of about mm'. It should be that most imported floors have no wide plate specification and thickened size.

A foot pad shall be placed in front of the door to reduce the wear of sand on the floor.After the wax on the ground has set, scrape off the protruding part along the ground with a plastic ruler or credit card. Defects.Good reputation,Note edit voiceLaminate flooring is a product with high scientific and technological content. From the appearance, it is very difficult to distinguish the quality unless it has been inspected.Therefore, we recommend that consumers buy brand products.Well known brands generally pass the test of market operation and have established a good image in the eyes of consumers.Well known brands not only ensure product quality, but also be responsible for laying and installation. More importantly, in the future, the service is guaranteed. If you buy it at ease, you can also avoid worries at home.Maybe the cheap floor can be or yuan cheaper than the brand floor per square meter, but its utility and service life may be only / or less of the brand floor, and there is a lack of environmental protection and after-sales service guarantee. Test: for the ground lacquer cloth with thin thickness, you can tear it by hand. If it can be easily torn off, the tear strength of such ground lacquer cloth can not meet the requirements. After gently rolling up and pressing down, if it can not be restored to the original state and leave an indentation, such a product has poor softness.If the layers can be torn by hand, it indicates that the product layers are not well combined, and stratification will soon occur in future use.Plastic floor paint cloth has the advantages of light weight, elasticity, good mechanical strength, good foot feeling strength, comfortable foot feeling, wear resistance, pollution resistance, corrosion resistance, heat insulation, sound insulation, moisture resistance, small water absorption, good insulation self extinguishing, easy cleaning, simple construction, convenient maintenance and low price. In a large number of civil buildings and public places, it has high requirements for cleanlinessIt is widely used in the laboratory.Plastic floor paint cloth belongs to soft floor. It is a floor coil produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.The length of each roll of plastic floor paint cloth is m ~ m, the width is mm ~ mm ~ mm, and the total thickness is mm (machine room) ~ mm (plant and public buildings)For long-term indoor use, high and medium grade products should be selected, and products produced by well-known brands and regular enterprises should be purchased as far as possible. Such products have sufficient thickness and good interlayer adhesion, and are not easy to layer and curl, especially foamed leather, which gives people a comfortable and elegant feeling. If you want to use them for a short time or one-time cover, you can choose low-grade products, but many of these products are processed with waste materials with poor flexibility, generally thin thickness and large shrinkage coefficient. When checking the appearance quality of rubber plastic floor paint cloth, it should be under scattered sunlight or fluorescent lamp, and the illumination should be ( ± LX, LM from the tested sample, conduct oblique visual inspection. First, observe whether there are cracks, fractures and delaminations on the surface of the local lacquer cloth. If there are,Frederick BayWhat are the types of wood flooring, it can be judged that the local lacquer cloth is unqualified. The second step is to observe whether there are wrinkle marks, bubble pollution points and pattern deformation. Those that cannot be observed are excellent products and first-class products; those that are slight but not obvious are recognized as qualified. Go back to the third step for observationIf there is any missing pattern on the surface of the ground lacquer cloth, or if there is any defect of the transparent wear-resistant film on the surface it is the first-class product and the first-class product. If there is a slight missing print or lack of film, otherwise it is the unqualified product. Finally it is the qualified product, carefully check whether there is deviation in the multi-color overprint on the surface, if the top-class product is uneven,Frederick BayHow to wrap wooden floor for steel frame stairs, if there are the above two defects, but if there is no obvious, it is the first-class productProducts that obviously have the above defects but do not affect the overall beauty are judged as qualified products. Finally, the appearance quality of ground lacquer cloth is determined based on the above judgment. When selecting ground lacquer cloth, first smell whether it has pungent smell. There will be a slight smell after the good coil is opened, and the smell of inferior products is stronger; secondly, and the same room should be selectedCoiled materials with the same batch number, pattern and thickness. When purchasing, carefully observe the appearance quality, open a roll of ground lacquer cloth, separate the ends for a few meters, observe the surface layer of the sample, the surface layer is thick, the wear-resistant layer is thick, and the service time is long, and then observe whether there are cracks, fractures, wrinkles, bubbles and large defects; whether the cross section is layered and cracked; whether the pattern is open, missing, lack of film and overprint deviationDefects such as color difference, color difference and pollution.

The density of laminate floor substrate (high density fiberboard) shall be .-. g / cm, and it is not appropriate to have too low or too high density.Quality improvement,Secondly, choose the color you want.The dark colors completely set off the serious atmosphere.One of the characteristics of industrial style is that it is not decorated, and there is no more suitable material than log. Log floor has a heavy sense of history and looks more flavor.The log material looks more natural, and the cold feeling brought by punching metal. Daily maintenance does not need waxing. It can be wiped with towel or wet mop. It is widely used in indoor families, hospitals, studies office buildings, factories, supermarkets, businesses, gymnasiums and other places.SPC floor is mainly composed of a certain proportion of calcium powder and PVC stabilizer to form a composite floor paving material.It is a new material invented in response to national emission reduction, hard SPC indoor floor.SPC floor takes calcium powder as the main raw material. After plasticizing and extruding sheet, four roll calendering hot compress color film decorative layer and wear-resistant layer,The combination of hardness and softness.The wood floor in the living room should be made of boards without knots cracks and mildew. Generally, Fraxinus mandshurica, because their lines are beautiful and clear, but it is required to have a certain carpentry foundation.Firstly, the wood board shall be processed into the length and width coordinated with the room size according to the room size, and the floor shall be cleaned before laying.When laying, draw the center point and vertical and horizontal vertical lines of the room, and lay from the center to the four sides. glue and an appropriate amount of cement can be used for bonding between laths.Note that the glue must be coated evenly to avoid the warping of the plate.Mute that is, add cork cushion or other cushion similar to cork on the back of the floor.After using the cork floor mat, the noise of stepping on the floor can be reduced by more than dB (quoted from the data of the cork floor mat factory), which can increase the foot feeling, sound absorption and sound insulation.This plays a positive role in improving the comfort of laminate flooring.It is also a direction for the future development of laminate flooring.Impregnated paper laminated wood floor is a floor made of one or more layers of special paper impregnated with thermosetting amino resin, which is paved on the surface of wood-based board substrate such as particleboard and high-density fiberboard, with a balanced moisture-proof layer on the back and a wear-resistant layer and decorative layer on the front. It is hot pressed and formed. First, it is divided into thin and thick (more than mm and about mm in thickness).