HolkinVertical centrifugal slurry pumpWhy is your flexibility getting better and better

　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the waterHolkin,　　When assembling the motor and water pump departments below grade ,HolkinSubmersible slurry pump, firstly, tighten the nuts evenly between the water inlet joint and the contact plane from the upper part to the bearing seat, install the coupling, pump shaft, fixed studs and lock rings, fix the impeller and conical sleeve on the pump shaft with a damp cylinder, and install the guide housing and impeller　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well, we should chooseInnsbruck,　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.

　　Now you know the reason why the pump has air turbidity. In fact, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, oil, liquid metal, acid-base night and so on. It is a good means of transport.　　Correct the main shaft of the water pump and adjust the position of the water pump and the motor relatively.　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. WhenBidding,　　Potential energy,HolkinVertical slurry pump, pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?　　Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment.　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, so it is also a reminder that we are using it too

　　 A vent pipe is installed at the bottom of the pump, so that when the pump is buried underground, water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even ifDesign brand,　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　Transmission type: direct drive, parallel belt drive, upper and lower belt drive CV vertical belt drive, etc. A variety of speeds and variants are adopted to make the pump operate under the best working conditions. It has long service life and high operation efficiency, resulting in poor heat dissipation effect.Holkin, that is the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　 Another possibility is that the gas is sucked in when the pump is in use.　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, because it does not need too many auxiliary facilities.