SOSTAluminum alloy hydraulic lifting platformApplication processing method

Check and repair the electrical circuit and control panel switch components. If there is aging in the circuit, replace itWhen disassembling the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts, it is necessary to avoid dust during the system oil passage. The disassembled parts must be thoroughly cleaned before opening. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap. After loosening the tank cap, remove any remaining debris from the joint area (do not rinse with water to prevent water from seeping into the tank). Only after confirming cleanliness can the tank cap be opened. When using materials and hammers, materials that do not remove fiber impurities and specialized hammers with rubber attached to the surface should be selected. Hydraulic components and hydraulic hoses should be carefully cleaned, dried with high-pressure air, and then assembled. Choose a well packaged filter element (the inner packaging is damaged, although the filter element is intact, it may also be unclean). When changing the oil, clean the filter at the same time. Before installing the filter element carefully clean the bottom dirt inside the filter housing with materials.SOST,Power supply voltage: Motor power: Lifting: Rocker self reset switch operation Overload protection: Over current relay.Regarding the construction elevator with counterweight, check the adjustment and fixation status of the counterweight guide wheel. Check the balancing equipment of the steel wire rope, the crown wheel, and the counterweight steel wire rope bracketJoal-Fadiout,Use a feeler gauge to check the wear condition of the worm gear of the worm gear reducer. Please refer to the instruction manual for specific requirementsWhen loosening occurs, newly processed and assembled components have deviations in geometric shape and fitting dimensions. In the early stages of use, due to alternating loads such as impact and vibration, as well as factors such as heat and deformation, coupled with rapid wear and tear, it is easy to cause the previously fastened components to loosen.Check the fastening status of the wall bracket, support rod, and bolts and retaining rings between the lifting cargo elevator and the bridge. If they are loose or displaced, they should be checked and tightened

Check the safety interlocking equipment of the first cut door of the hanging cageDuring aging treatment, the equipment prints the vibration aging curve online. According to the curve, the front end of the a-t curve shows an upward trend indicating that the damping inside the component decreases after vibration treatment, so the amplitude gradually increases; Since then, the amplitude change has been basically stable, which conforms to the judgment standard of curve observation strip, and hang it in a prominent position. When working on an electric lifting platform, professional drivers and operators must be equipped, and they must undergo specialized training and be qualified. They must hold relevant certificates and take on corresponding responsibilities according to the actual situation of the work. After the construction is completed, the lifting platform needs to be moved on the site and should be operated by a professional driver. Before daily work,SOSTCylinder mounted hydraulic lifting platform, zy drivers must carefully check the electrical, hydraulic,SOSTSelf walking scissor fork lifting platform, and mechanical systems of the platform,SOSTCar mounted aluminum alloy elevator, check the working range of the lifting platform truck, and remove obstacles that hinder the rotation and walking of the lifting platform truck. And empty the platform up and down several times to check for any faults or abnormal phenomena. It is also necessary to pay attention to the accuracy of the platform platform landing station for any obvious abnormal differences. Professional improvement of quality assurance for aircraft manufacturers. The promotional activity is ongoing, and new and old customers are welcome to come for consultationUse a feeler gauge to check the wear condition of the worm gear of the worm gear reducer. Please refer to the instruction manual for specific requirementsproduction,After cleaning, and the brush pressure should be adjusted to ensure that its area is not less than %.Check the safety interlocking equipment of the first cut door of the hanging cage

Lifting and loweringInstallation materialsCheck the safety interlocking equipment of the first cut door of the hanging cageAccording to calculations, when the support points of the beam type components are located along the length of /L on both sides, the vibration resistance is relatively small, making it easy to obtain resonance and vibration effects with larger amplitudes. The geometric shape of the structure on the lifting foundation is similar to a long beam type component, and the structure is complex. Therefore, two support points should be taken on each side for time treatment.Check if the orientation of the upper and lower limit blocks on the guide rail frame is correctSOST,Clean and inspect the crown wheel frame assembly, correct or replace with new partsCheck the smooth steel wire rope and various fasteners, if there is excessive wear, it is necessary to replace themAll connecting shafts must have split pins and be sufficient.